基于二噻吩并吡咯π桥的窄带隙非富勒烯受体材料在有机太阳能电池中的应用

doi:10.11944/j.issn.1000-0518.2019.09.190048

摘要/Abstract

摘要：

以不同烷基取代的二噻吩并吡咯(DTP)为π桥,连接吲哒省并二噻吩(IDT)中间单元和氰基茚酮(IC)或二氟代氰基茚酮(2F-IC)末端基团,设计并合成了6个窄带隙的非富勒烯受体材料。其中,IDTDTP-C₂C₂-H和IDTDTP-C₂C₂-F中的DTP单元以1-乙基丙基为侧链,IDTDTP-C₆C₆-H和IDTDTP-C₆C₆-F中的DTP单元以1-己基庚基为侧链,IDTDTP-C₁₂-H和IDTDTP-C₁₂-F中的DTP单元以十二烷基为侧链。 6个分子均具有较窄的光学带隙(1.37~1.44 eV)。相比于以IC为末端基团的分子(IDTDTP-C₂C₂-H、IDTDTP-C₆C₆-H和IDTDTP-C₁₂-H),由于氟原子的拉电子效应,以2F-IC为末端基团的分子(IDTDTP-C₂C₂-F、IDTDTP-C₆C₆-F和IDTDTP-C₁₂-F)具有红移的吸收光谱,以及更低的最高分子占有轨道能级(HOMO)和最低分子空轨道(LUMO)能级。以宽带隙聚合物聚[2,6-(4,8-双(5-(2-乙基己基))噻吩-2-基)-苯并[1,2-b:4,5-b']二噻吩-alt-5,5-(1',3'-二-2-噻吩)-5',7'-双(2-乙基己基)-苯并[1',2'-c:4',5'-c']二噻吩-4,8-二酮](PBDB-T)为给体材料,制备了有机太阳能电池器件。 PBDB-T:IDTDTP-C₆C₆-F共混薄膜具有较高且更平衡的空穴/电子迁移率,以及良好的形貌,基于PBDB-T:IDTDTP-C₆C₆-F的有机太阳能电池获得了6.94%的能量转换效率,开路电压为0.86 V,短路电流密度为13.56 mA/cm²,填充因子为59.5%。

关键词: 有机太阳能电池, 非富勒烯受体, 二噻吩并吡咯, 烷基侧链, 能量转换效率

Abstract:

A series of non-fullerene acceptors with dithieno[3,2-b:2',3'-d]pyrrole(DTP) π bridge to link indacenodithiophene(IDT) core and 3-(dicyanomethylidene)indan-1-one(IC) or difluorinated IC(2F-IC) terminals, i.e. IDTDTP-C₂C₂-H and IDTDTP-C₂C₂-F with 1-ethylpropyl on DTP, IDTDTP-C₆C₆-H and IDTDTP-C₆C₆-F with 1-hexylheptyl on DTP, and IDTDTP-C₁₂-H and IDTDTP-C₁₂-F with n-dodecyl on DTP, was designed and synthesized. These molecules achieved low optical band gaps(1.37~1.44 eV). Compared with the IC-terminated molecules(IDTDTP-C₂C₂-H, IDTDTP-C₆C₆-H and IDTDTP-C₁₂-H), IDTDTP-C₂C₂-F, IDTDTP-C₆C₆-F and IDTDTP-C₁₂-F with 2F-IC as terminals show red-shifted absorption spectra and down-shifted the highest occupied molecular orbitals(HOMO) and the lowest unoccupied molecular orbitals(LUMO) energy levels owing to the electron-withdrawing ability of F substituents. Organic solar cells(OSCs) based on these acceptors were fabricated with the wide-bandgap polymer poly[2,6-(4,8-bis(5-(2-ethylhexyl))thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene-alt-5,5-(1',3'-di-2-thienyl)-5',7'-bis(2-ethylhexyl)-benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione](PBDB-T) as the donor. Owing to the higher and more balanced hole and electron mobilities, and a proper phase-separated morphology in the blend film, IDTDTP-C₆C₆-F with 1-hexylheptyl on DTP unit achieved a maximum power conversion efficiency(PCE) of 6.94% with an open-circuit voltage(V_oc) of 0.86 V, a short circuit current density(J_sc) of 13.56 mA/cm² and a fill factor(FF) of 59.5%.

Key words: organic solar cell, non-fullerene acceptor, dithienopyrrole, alky side chain, power conversion efficiency

张小梅, 李淼淼, 王琪, 江宇, 耿延候. 基于二噻吩并吡咯π桥的窄带隙非富勒烯受体材料在有机太阳能电池中的应用[J]. 应用化学, 2019, 36(9): 1023-1034.

ZHANG Xiaomei, LI Miaomiao, WANG Qi, JIANG Yu, GENG Yanhou. Near-infrared Absorbing Non-fullerene Acceptors with Dithienopyrrole as π Spacer for Organic Solar Cells[J]. Chinese Journal of Applied Chemistry, 2019, 36(9): 1023-1034.

参考文献

[1]	Cheng Y J,Yang S H,Hsu C S.Synthesis of Conjugated Polymers for Organic Solar Cell Applications[J]. Chem Rev,2009,109(11):5868-5923.
[2]	Li Y F.Molecular Design of Photovoltaic Materials for Polymer Solar Cells:Toward Suitable Electronic Energy Levels and Broad Absorption[J]. Acc Chem Res,2012,45(5):723-733.
[3]	Li G,Zhu R,Yang Y.Polymer Solar Cells[J]. Nat Photonics,2012,6:153-161.
[4]	Kim T,Kim J H,Kang T E,et al. Flexible, Highly Efficient All-Polymer Solar Cells[J]. Nat Commun,2015,6:8547-8553.
[5]	Sun C,Pan F,Bin H,et al. A Low Cost and High Performance Polymer Donor Material for Polymer Solar Cells[J]. Nat Commun,2018,9:743-752.
[6]	Guo X,Zhou N,Lou S J,et al. Polymer Solar Cells with Enhanced Fill Factors[J]. Nat Photonics,2013,7:825-833.
[7]	Wang M,Hu X,Liu P,et al. Donor-Acceptor Conjugated Polymer Based on Naphtho[1,2-c:5,6-c]bis[1,2,5]thiadiazole for High-Performance Polymer Solar Cells[J]. J Am Chem Soc,2011,133(25):9638-9641.
[8]	Wu W,Zhang G,Xu X,et al. Wide Bandgap Molecular Acceptors with a Truxene Core for Efficient Nonfullerene Polymer Solar Cells:Linkage Position on Molecular Configuration and Photovoltaic Properties[J]. Adv Funct Mater,2018,28(18):1707493.
[9]	Liu J,Chen S,Qian D,et al. Fast Charge Separation in a Non-fullerene Organic Solar Cell with a Small Driving Force[J]. Nat Energy,2016,1:16089.
[10]	Li S,Ye L,Zhao W,et al. Energy-Level Modulation of Small-Molecule Electron Acceptors to Achieve over 12% Efficiency in Polymer Solar Cells[J]. Adv Mater,2016,28(42):9423-9429.
[11]	Qiu N,Zhang H,Wan X,et al. A New Nonfullerene Electron Acceptor with a Ladder Type Backbone for High-Performance Organic Solar Cells[J]. Adv Mater,2017,29(6):1604964.
[12]	Yang Y,Zhang Z G,Bin H,et al. Side-Chain Isomerization on an N-Type Organic Semiconductor ITIC Acceptor Makes 11.77% High Efficiency Polymer Solar Cells[J]. J Am Chem Soc,2016,138(45):15011-15018.
[13]	Cheng P,Li G,Zhan X,et al. Next-Generation Organic Photovoltaics Based on Non-fullerene Acceptors[J]. Nat Photonics,2018,12:131-142.
[14]	Lin Y,Wang J,Zhang Z G,et al. An Electron Acceptor Challenging Fullerenes for Efficient Polymer Solar Cells[J]. Adv Mater,2015,27(7):1170-1174.
[15]	Lin Y,Zhang Z G,Bai H,et al. High-Performance Fullerene-Free Polymer Solar Cells with 6.31% Efficiency[J]. Energy Environ Sci,2015,8:610-616.
[16]	Lin Y,Zhao F,He Q,et al. High-Performance Electron Acceptor with Thienyl Side Chains for Organic Photovoltaics[J]. J Am Chem Soc,2016,138(14):4955-4961.
[17]	Zhao F,Dai S,Wu Y,et al. Single-Junction Binary-Blend Nonfullerene Polymer Solar Cells with 12.1% Efficiency[J]. Adv Mater,2017,29(18):1700144.
[18]	Liu F,Zhou Z,Zhang C,et al. A Thieno[3,4-b]thiophene-Based Non-fullerene Electron Acceptor for High-Performance Bulk-Heterojunction Organic Solar Cells[J]. J Am Chem Soc,2016,138(48):15523-15526.
[19]	Li R,Liu G,Xie R,et al. Introducing Cyclic Alkyl Chains into Small-molecule Acceptors for Efficient Polymer Solar Cells[J]. J Mater Chem C,2018,6:7046-7053.
[20]	Liu Y,Zhang Z,Feng S,et al. Exploiting Noncovalently Conformational Locking as a Design Strategy for High Performance Fused-Ring Electron Acceptor Used in Polymer Solar Cells[J]. J Am Chem Soc,2017,139(9):3356-3359.
[21]	Zhao W,Li S,Yao H,et al. Molecular Optimization Enables over 13% Efficiency in Organic Solar Cells[J]. J Am Chem Soc,2017,139(21):7148-7151.
[22]	Li R,Liu G,Xiao M,et al. Non-Fullerene Acceptors Based on Fused-ring Oligomers for Efficient Polymer Solar Cells via Complementary Light-Absorption[J]. J Mater Chem A,2017,5:23926-23936.
[23]	Sun J,Ma X,Zhang Z,et al. Dithieno[3,2-b:2',3'-d]pyrrol Fused Nonfullerene Acceptors Enabling over 13% Efficiency for Organic Solar Cells[J]. Adv Mater,2018,30(16):1707150.
[24]	Xu X,Yu T,Bi Z,et al. Realizing over 13% Efficiency in Green-Solvent-Processed Nonfullerene Organic Solar Cells Enabled by 1,3,4-Thiadiazole-Based Wide-Bandgap Copolymers[J]. Adv Mater,2018,30(3):1703973.
[25]	Zhao W,Zhang S,Zhang Y,et al. Environmentally Friendly Solvent-Processed Organic Solar Cells that are Highly Efficient and Adaptable for the Blade-Coating Method[J]. Adv Mater,2018,30(4):1704837.
[26]	Li S,Ye L,Zhao W,et al. A Wide Band Gap Polymer with a Deep Highest Occupied Molecular Orbital Level Enables 14.2% Efficiency in Polymer Solar Cells[J]. J Am Chem Soc,2018,140(23):7159-7167.
[27]	Xiao Z,Jia X,Ding L.Ternary Organic Solar Cells Offer 14% Power Conversion Efficiency[J]. Sci Bull,2017,62:1562-1564.
[28]	Li W,Hendriks K H,Wienk M M,et al. Diketopyrrolopyrrole Polymers for Organic Solar Cells[J]. Acc Chem Res,2016,49(1):78-85.
[29]	You J,Dou L,Yoshimura K,et al. A Polymer Tandem Solar Cell with 10.6% Power Conversion Efficiency[J]. Nat Commun,2013,4:1446-1455.
[30]	Li W,Furlan A,Hendriks K H,et al. Efficient Tandem and Triple-Junction Polymer Solar Cells[J]. J Am Chem Soc,2013,135(15):5529-5532.
[31]	Chang C Y,Zuo L,Yip H L,et al. A Versatile Fluoro-Containing Low-Bandgap Polymer for Efficient Semitransparent and Tandem Polymer Solar Cells[J]. Adv Funct Mater,2013,23(40):5084-5090.
[32]	Zhou E,Wei Q,Yamakawa S,et al. Diketopyrrolopyrrole-Based Semiconducting Polymer for Photovoltaic Device with Photocurrent Response Wavelengths up to 1.1 μm[J]. Macromolecules,2010,43(2):821-826.
[33]	Bai H,Wang Y,Cheng P,et al. An Electron Acceptor Based on Indacenodithiophene and 1,1-Dicyanomethylene-3-Indanone for Fullerene-Free Organic Solar Cells[J]. J Mater Chem A,2015,3(5):1910-1914.
[34]	Yao H,Chen Y,Qin Y,et al. Design and Synthesis of a Low Bandgap Small Molecule Acceptor for Efficient Polymer Solar Cells[J]. Adv Mater,2016,28(37):8283-8287.
[35]	Cui Y,Yang C,Yao H,et al. Efficient Semitransparent Organic Solar Cells with Tunable Color Enabled by an Ultralow-Bandgap Nonfullerene Acceptor[J]. Adv Mater,2017,29(43):1703080.
[36]	Yao H,Cui Y,Yu R,et al. Design, Synthesis, and Photovoltaic Characterization of a Small Molecular Acceptor with an Ultra-Narrow Band Gap[J]. Angew Chem Int Ed,2017,56(11):3045-3049.
[37]	Yan C,Wu Y,Wang J,et al. Enhancing Performance of Non-Fullerene Organic Solar Cells via Side Chain Engineering of Fused-Ring Electron Acceptors[J]. Dyes Pigm,2017,139:627-634.
[38]	Liang Z,Li M,Zhang X,et al. Near-Infrared Absorbing Non-Fullerene Acceptors with Selenophene as π Bridges for Efficient Organic Solar Cells[J]. J Mater Chem A,2018,6:8059-8067.
[39]	Liu F,Zhou Z,Zhang C,et al. Efficient Semitransparent Solar Cells with High NIR Responsiveness Enabled by a Small-Bandgap Electron Acceptor[J]. Adv Mater,2017,29(21):1606574.
[40]	Duan C,Franeker J J,Wienk M M,et al. High Open Circuit Voltage Polymer Solar Cells Enabled by Employing Thiazoles in Semiconducting Polymers[J]. Polym Chem,2016,7:5730-5738.
[41]	Duan C,Gao K,Colberts F J M,et al. Thiophene Rings Improve the Device Performance of Conjugated Polymers in Polymer Solar Cells with Thick Active Layers[J]. Adv Energy Mater,2017,7(19):1700519.
[42]	Hou J,Inganas O,Friend R H,et al. Organic Solar Cells Based on Non-fullerene Acceptors[J]. Nat Mater,2018,17(2):119-128.
[43]	Huang C,Liao X,Gao K,et al. Highly Efficient Organic Solar Cells Based on S,N-Heteroacene Non-fullerene Acceptors[J]. Chem Mater,2018,30(15):5429-5434.
[44]	Yue W,Zhao Y,Shao S,et al. Novel NIR-Absorbing Conjugated Polymers for Efficient Polymer Solar Cells:Effect of Alkyl Chain Length on Device Performance[J]. J Mater Chem,2009,19:2199-2206.
[45]	Zhou E,Nakamura M,Nishizawa T,et al. Synthesis and Photovoltaic Properties of a Novel Low Band Gap Polymer Based on N-Substituted Dithieno[3,2-b:2',3'-d]pyrrole[J]. Macromolecules,2008,41(22):8302-8305.
[46]	Duan C,Willems R E M,Franeker J J,et al. Effect of Side Chain Length on the Charge Transport, Morphology, and Photovoltaic Performance of Conjugated Polymers in Bulk Heterojunction Solar Cells[J]. J Mater Chem A,2016,4:1855-1866.
[47]	Bin H,Gao L,Zhang Z G,et al. 11.4% Efficiency Non-Fullerene Polymer Solar Cells with Trialkylsilyl Substituted 2D-Conjugated Polymer as Donor[J]. Nat Commun,2016,7:13651-13661.
[48]	Wang J,Wang S,Duan C,et al. Conjugated Polymers Based on Difluorobenzoxadiazole Toward Practical Application of Polymer Solar Cells[J]. Adv Energy Mater,2017,7(22):1702033.
[49]	Jia X,Chen Z,Duan C,et al. Polythiophene Derivatives Compatible with Both Fullerene and Non-fullerene Acceptors for Polymer Solar Cells[J]. J Mater Chem C,2019,7:314-323.
[50]	Yang Y,Zhang Z G,Bin H,et al. Side-Chain Isomerization on an n-type Organic Semiconductor ITIC Acceptor Makes 11.77% High Efficiency Polymer Solar Cells[J]. J Am Chem Soc,2016,138(45):15011-15018.
[51]	Liu X,Zhang C,Duan C,et al. Morphology Optimization via Side Chain Engineering Enables All-Polymer Solar Cells with Excellent Fill Factor and Stability[J]. J Am Chem Soc,2018,140(28):8934-8943.
[52]	Liu X,Xie B,Duan C,et al. A High Dielectric Constant Non-Fullerene Acceptor for Efficient Bulk-Heterojunction Organic Solar Cells[J]. J Mater Chem A,2018,6:395-403.
[53]	Chen S,Lee K C,Zhang Z G,et al. An Indacenodithiophene-Quinoxaline Polymer Prepared by Direct Arylation Polymerization for Organic Photovoltaics[J]. Macromolecules,2016,49(2):527-536.
[54]	Perera I R,Gupta A,Xiang W,et al. Introducing Manganese Complexes as Redox Mediators for Dye-Sensitized Solar Cells[J]. Phys Chem Chem Phys,2014,16:12021-12028.
[55]	Zhang Z G,Qi B,Jin Z,et al. Perylene Diimides:A Thickness-Insensitive Cathode Interlayer for High Performance Polymer Solar Cells[J]. Energy Environ Sci,2014,7:1966-1973.
[56]	Wu Y,Yang H,Zou Y,et al. A New Dialkylthio-Substituted Naphtho[2,3-c]thiophene-4,9-dione Based Polymer Donorfor High-Performance Polymer Solar Cells[J]. Energy Environ Sci,2019,12(2):675-683.
[57]	Guo B,Li W,Guo X,et al. High Efficiency Nonfullerene Polymer Solar Cells with Thick Active Layer and Large Area[J]. Adv Mater,2017,29(36):1702291.
[58]	Fan Q,Wang Y,Zhang M,et al. High-Performance As-Cast Nonfullerene Polymer Solar Cells with Thicker Active Layer and Large Area Exceeding 11% Power Conversion Efficiency[J]. Adv Mater,2018,30(6):1704546.